How to Apply for Comprehensive Exam in PUP (2019)

1. Download the form from the PUP website. https://www.pup.edu.ph/gs/forms
    The form should look like this:
2. Fill up the Comprehensive Exam Form.
3. Fill up the updated Program of Studies (Curriculum Sheet)
4. Qualified to take the comprehensive examination are those who have completed ALL academic course requirements of the program or those who are completing them on that semester.
5. For those who are just just completing on that semester, make sure to secure a copy of your grades from your SIS account. 
6. After filling up and completing your requirements, go to the cashier (GS or Main Building) and pay for Php150.00 and secure the O.R. 
7. Before submitting all the requirements, make sure you have a clearance from the GS library and Accounting Office(Main building).

 8. Give it to the faculty officers and don't forget to to sign in the logbook. 

 NOTE:
 Only those with complete academic and non-academic credential/requirements shall be processed and approved.

     Academic Deficiencies:
  • Copy of Registration Certificates
  • Completion of Incomplete grades
  • Unsubmitted gradesheets
  • Application of readmission (for returning students)
   Non-Academic Requirements:
  • Original Transcript of Records ("Copy for PUP") from school last attended
  • Correction of Information/data in school records (i.e. discrepancy of name/change or correction of name)
That's it! Good Luck! This article is for Graduate School Students.
For more info, visit https://www.pup.edu.ph/

 For any questions, please leave a comment below 

Comments

Post a Comment

Popular posts from this blog

Design Guide for Car Parking in the Philippines (2019)

Image
Design Guide for Car Parking in the Philippines (2019) 1. Minimum Dimension for Car Parking Automobile Classification Width(m) Length(m) Orientation Total Area(m²) Average Car 2.50 5.00 Perpendicular or Diagonal 12.50 Average Car 2.15 6.00 Parallel Parking 12.90 Standard Truck or Bus 3.60 12.00 All 43.20 Articulated Truck 3.60 18.00 All 64.80 Jeepney or Shuttle 3.00 9.00 All 27.00 2. Height for Car Parking     For height of car park inside the building, we can use 2.0m - 2.40m clear height. 3. Standard Driveway Width     No specific width from the code but we can use 3.0 m minimum. 4. Standard Driveway Slope      5. Driveways across sidewalks  To maximize the use of the sidewalk area, the surface of the sidewalk and the driveway shall as much as possible, be at the same place. The entry ramp of the driveway connecting the roadway s
Read more

Engineering Terms in Filipino You Should Know

Image
These are the 30 Engineering Terms in Filipino You Should Know 1. Alulod (Drain) - is part of building's water discharge system 2. Baytang (Tread) - is the horizontal portion of a set of stairs on which a person walks 3. Biga  (Beam) - is a structural element that primarily resists loads applied laterally to the beam's axis 4. Bisagra (Hinge) - is a mechanism that connects normally a door, window or other construction element, to either a frame or a cabinet of some type 5. Guililan (Girder) - it is the main horizontal support of a structure which supports smaller beams 6. Hamba (Jamb) - is the side-post or lining of a doorway or other aperture 7. Hulog - (Plumb bob) - a metal weight attached to the end of a plumb line. Used to establish vertical line 8. Kapak (Bulge) - honeycomb air pockets that form on the concrete 9. Masilya (Putty) - is a material with high plasticity, similar in texture to clay or dough, typically used in domestic construction and repair
Read more

How to Plot Land Title Boundary Using AutoCAD

Image
How to Plot Land Title Boundary Using AutoCAD (2019) 1. Open your AutoCAD. 2. Type DDUNITS to open the Drawing Units. 3. Change the units with the values below 4. At the Direction, choose your desired direction 5. Pick a point to start the line or polyline      Example: N 12 DEG. 25'E, 8180 mm                    S 78 DEG. 41'E, 5350 mm                     S 14 DEG. 41'W, 22080 mm                     N 75 DEG. 28'W, 4480 mm                     N 12 DEG. 25'E, 13610 mm (to the point of start)      Should input like this:                    @8180< N12d25'E                    @5350<S78d41'E                    @22080< S14d41'W                    @4480< N75d28'W                    @13610< N12d25'E (to the point of start) 6. The final drawing should look like this That's it! You should give it a try! For any questions, just comment below!
Read more